GM (General Motors)
- 1998-2002 F-Body
- 2004-2006 GTO
- C5 Corvette
- C6 Corvette / C6 Z06
- C6 ZR1 Corvette
- C7 Corvette
- 2004-2007 CTS-V
- 2009-Present CTS-V
- G8 GXP
- Gen 5 Camaro
- Gen 5 Z28 Camaro
- Gen 5 ZL1 Camaro
- Gen 6 Camaro
LT-1 Twin Disc Install Tips
MONSTER CLUTCH CO. LT-1 TWIN DISC INSTALL TIPS
Thank you for purchasing a Monster Clutch product! Here are a few very important things to keep in mind when installing your Monster Clutch Co. LT1-xx based multi-disc clutch. If you have any questions about your installation, please give us a call at 817-750-2000 or email us at firstname.lastname@example.org.
We do not recommend inexperienced technicians install these units, that said, if you get stuck or are not sure about something STOP IMMEDIATELY AND CONTACT US! Ignoring things or getting something wrong during the installation can be very costly in the end and is not covered under our warranty – when in doubt ASK!
- ON ALL SC, R, AND RR MULTI-DISC UNITS – DO NOT - FOR ANY REASON - REMOVE THE BOLTS ATTACHING THE UPPER FLOATER PLATE TO THE PRESSURE PLATE. DOING SO WILL RENDER THE CLUTCH USELESS AND WILL CAUSE A SEVERE IMBALANCE, IF YOU’VE DONE THIS DO NOT ATTEMPT TO USE THE CLUTCH, CONTACT US IMMEDIATELY!!!!!!!!!
- DO NOT USE ARP hardware with our multi-disc units, using ARP flywheel bolts with this unit will cause immediate damage and failure as it will interfere with the lower disc. We’ve included modified GM flywheel bolts with your clutch, there is no need to use anything else.
- Use Red Loctite on the six (6) pressure plate bolts.
- DO NOT LUBRICATE THE PILOT BEARING OR INPUT SHAFT
- Our clutches typically do not require shimming of the slave cylinder. That said, we recommend measuring your setup to ensure things are as they should be. There are multiple tolerances at play (bell housing, transmission case, clutch assembly, crankshaft flange, and engine block) that can be off one way or another, by measuring you ensure that your entire setup, not just the clutch, is correct and within tolerance. See our FAQ page for information on how to measure and what tolerances you should see (under “Does my clutch need a shim”).
- Quick Time/aftermarket bellhousings will almost always need some sort of a shim – their tolerances are quite a bit different than OEM and vary from part to part.
- Never attempt to measure the setup with a tape measure, you must always use a set of calipers – whether they are digital or not does not matter, as long as you can read them. If you contact us with measurements, they must be to the .001” or we cannot help you.
- All Monster Clutch Co. multi-disc units are put through multiple tests prior to leaving our facility. We go through great lengths to ensure you’re getting a clutch that is 100% ready to install when it arrives. In short, when it leaves here it is a perfectly working/functioning clutch – if something is amiss during installation or break in it is your (installer/consumer) responsibility to contact us prior to continued installation/usage. Any damages that occur from an improperly installed clutch are not covered under our warranty.
- Make sure that all friction mating surfaces are clean. Spray brake cleaner on a rag and wipe the surfaces down to get all of the packing oils, etc. off of the surfaces. This is important as fluid contamination is the #1 reason for chatter as well as friction failure and is NOT covered under our warranty.
These clutches come preassembled. Make sure that you reassemble the unit as you pulled it a part to ensure proper operation. We recommend that you mark things as you disassemble and clean them with a permanent marker (or take images with your cell phone), this will help things go back together smoothly and keep you from forgetting if you must walk away from your project.
There are three round aluminum stands that can spin when installing them and the direction of them does not matter. There are three pinned rectangle aluminum stands that must go on as they come out of the package (Monster “hair” facing out and towards the transmission); failure to do this will result in the clutch not operating properly. All disc hubs face the transmission, do not face the disc hub on the lower disc towards the flywheel, doing so will cause damage and release issues!
Flywheel bolts are torqued in three phases, the torque specs are 15-37-74 ft/lbs of torque. The torque sequence is 1-4-6-2-5-3 for 6-bolt flywheels, 1-5-7-3-8-4-6-2 for 8-bolt flywheels, and 1-5-8-3-6-2-7-4-9 for 9-bolt flywheel.
Pressure plate bolts are torqued in three phases, the torque specs are 20-40-52 ft/lbs of torque. The torque sequence is 1-4-6-2-5-3
IF YOUR CAR STILL HAS A FACTORY CLUTCH PEDAL ASSIST SPRING REMOVE IT BEFORE DRIVING, THIS WILL ALLOW A MORE LINEAR PEDAL FEEL AND WILL IMPROVE THE DRIVING CHARACTERISTICS OF THE UNIT.
ENJOY YOUR NEW MONSTER!
- C7 Corvette